Xbox 360 3 Red Lights Fix Guide Complete (Part II/End) : Step Ten
Now with the motherboard removed, flip it over and find the two X connectors
on the bottom of it. These are what hold the heat sinks on the CPU & GPU. Be
EXTREMELY careful when removing these. It takes a little force, this could
destroy your 360 if not applied properly and carefully. Just keep VERY GENTLY
trying each one until you get them to release. I myself like to use a small pointy
probe tool, carefully inserting it into each one until they release. I also try to stay
away from the tiny black memory chips when doing this. Just remember take
your time and be very careful and you will have no problems with this step.
Step Eleven:
In this step you will be removing the thermal compound from the GPU and CPU
and Heat sinks
You can remove the thermal compound with the end of a plastic Q-tip
and Rubbing Alcohol (slow) or the Arctic Cleaning Kit with a soft cloth (fast).
Clean the GPU and CPU with thermal compound cleaning solution and then wipe
the GPU and CPU with alcohol or use what I use in the video which is the Artic
Cleaning kit.
After you’ve removed the thermal compound you need to wipe it down really
good so that the GPU, CPU and Heat sinks Shine. To make the GPU and CPU
shine dab a little bit of rubbing alcohol onto a paper towel and wipe them done.
DO NOT touch the GPU, CPU or Heat sinks with your fingers after they are all
shiny.
This is what the old thermal compound should look like.
This is what a clean shiny GPU and CPU should look like Clean GPU and CPU
Step Twelve:
After you have cleaned the CPU and GPU heat sinks you will need to REPLACE
the thermal compound. Here is a small tutorial I found on eBay explaining how
to apply thermal compound. ( Click me for the tutorial ). Again, if you need to
purchase the thermal compound, you can find it at almost any local computer
shop or you can purchase it off eBay as well.
I wrap a piece of plastic bag around my finger and put only a dab (less than a
dime size) of Thermal Compound on the tip of my finger and gently wipe the
compound on the GPU and CPU. You just want to put a thin layer on it. You
shouldn’t be able to see the shinyness of the GPU and CPU.
This is what the new thermal compound on the GPU and CPU should look like
Step Thirteen: Replace the X clamps
Now you need to take the screws off your Heat sink and replace them with some
new screws and add some washers.
To remove the 4 pegs on each of the heat sinks use pliers or the correct wrench.
Turn the screws counter clock wise to unscrew the pegs. You will not need these
pegs any longer.
Step fourteen: Secure motherboard with bolts.
This the order you need to secure your heat sinks to your motherboard.
This is the order you need have. Zinc plated washer, nylon washer,
motherboard, nylon washer, zinc plated washer.
You need to attach both heat sinks to the motherboard. Above is a picture of
the process. Put a metal washer first then a nylon washer and then insert the
bolt into the mother board and now add another nylon washer and then
another metal washer for all 4 holes. Now align the heat skink and bolts
together and hand tighten the bolts to the motherboard, make sure no to
over tighten the bolts.
This is what you mother board should look like after heat sinks have been
secured with the bolts and washers.
Step fifteen: Secure the thermal compound bond.
Put your motherboard back into the metal case and attach dvd drive and plug
it in. Next attach the RF module and the white plastic cover. Do not put your
fan back yet.
Now plug you
xbox 360 power and av cable and turn on your xbox. To turn it
on poke the copper button on the middle of the RF module. Your xbox will
show the 3 red light error for about 1min 30 sec or so then it will only light
up the 2 left red lights which means your xbox is over heating which is
exactly what we want because we need the thermal compound to melt a little
so that the GPU, CPU and heat sinks can make full contact.
As soon as only the 2 left red lights are on wait 1 min to 1min 30sec and then
unplug you xbox and remove the dvd drive and the RF module. Be Very
Careful not to burn yourself. Your xbox will be HOT.
Use a towel and remove your motherboard from the metal case. Now you will
tighten the bolts that replaced the X clamps. Use pliers or the correct sized
socket and tighten all the bolts, do not tighten them so hard that you snap
your motherboard.
Now its time to let your xbox to completely cool down. Wait 20-30 min or
longer if the room is warm.
Step sixteen: Reassemble your xbox 360.
See video in the member’s area for a tutorial. Or put it back together without
the video its pretty dang easy.
You can now plug in the Xbox 360 and turn it on ☺
Hopefully your Xbox 360 works and you can now have the comfort of knowing
you saved a ton of money by not sending in the console to Microsoft! The 3 red
lights error most likely will not happen again, but if it does you now have the
knowledge of how to fix it. Please play the Xbox 360 on low settings for at least
20 days so it can set up and cure. Enjoy!
Xbox 360 3 Red Lights Fix Complete Guide (Part I/II) |
Xbox Live Codes
